Skip to content
Exclusive agent of MECH products in Saudi Arabia
Store Request a quote

MECH BMI CAP | MODEL 300

Model 300

Class
American Standard Class 150
Material
Malleable iron ASTM A197/A197M
Dimensions
ASME B16.3, B16.14 (unions B16.39)
Threads
ASME B1.20.1
Sizes
1/8" – 8"
Request a quote for this product
Or buy from the online store
SIZES & DIMENSIONS

Sizes & dimensions

SizeDNA min (mm)
1/8"DN613.5
1/4"DN816.0
3/8"DN1018.8
1/2"DN1522.1
3/4"DN2024.6
1"DN2529.5
1-1/4"DN3232.5
1-1/2"DN4033.8
2"DN5036.8
2-1/2"DN6543.2
3"DN8045.7
4"DN10052.8
5"DN12558.9
6"DN15064.8
8"DN20076.2
PROJECT APPROVALS

Approved on projects

96 projects and 64 owners approved this product or its family through the project consultants.

and 84 more projects.

Original approval letters are provided on request with your submittal.

The MECH cap in black malleable iron, model 300, American Standard Class 150, material ASTM A197/A197M, dimensions ASME B16.3, NPT threads (ASME B1.20.1), sizes 1/8″ – 8″, rated up to 300 psig from -29 to 66 °C, decreasing with temperature per the MECH pressure-temperature table. This guide explains what it does, related models, technical data, correct installation and common mistakes.

At a glance

  • A cap screws onto a male pipe end or fitting to close it; a plug screws into a female fitting.
  • Sizes 1/8″ – 8″, NPT threads.
  • Rated up to 300 psig from -29 to 66 °C, decreasing with temperature per the MECH pressure-temperature table.

What is a threaded cap and plug?

A cap screws onto a male pipe end or fitting to close it; a plug screws into a female fitting. A countersunk plug sits inside the fitting without projecting.

They close line ends, test and drain openings, and outlets not yet in use.

Related models

American Standard models of the same type
ModelItemSizes
300 — this productCAP1/8″ – 8″
291PLUG1/8″ – 6″

Technical data

Model 300 specification
ItemSpecification
ClassAmerican Standard Class 150
MaterialMalleable iron ASTM A197/A197M
DimensionsASME B16.3, B16.14 (unions B16.39)
ThreadsASME B1.20.1
Sizes1/8″ – 8″
Pressure vs temperature — Class 150 (from the MECH catalogue)
Temperature (°C)Pressure (psig)
-29 – 66300
100265
125225
150185

Dimensions for every size are in the size table at the top of the page. Per the MECH catalogue: tensile strength ≥ 350 MPa, elongation ≥ 10%.

Closing under pressure

A cap or plug at the end of a line carries full system pressure, so tighten it properly with a suitable sealant and never remove it while the line is under pressure.

Caution

Never mix NPT and BSPT threads: the joint may seem to make up but it will not seal and will leak under pressure.

Installation steps

  1. Make sure pipe and fitting have the same thread (NPT); never mix NPT and BSPT in one joint.
  2. Clean and inspect the threads, then apply a suitable sealant (PTFE tape or a thread compound approved for the fluid) to the male thread only.
  3. Screw the fitting on by hand first, then finish with a wrench for a reasonable number of turns without over-tightening; excessive tightening can split the fitting.
  4. Support the pipework properly so threaded joints do not carry extra weight or bending.
  5. Pressure-test the line to the project specification before commissioning.

Common mistakes

  • Mixing American NPT and British BSPT fittings in the same line.
  • Over-tightening with a wrench or using extension bars, cracking the fitting.
  • Wrapping PTFE tape the wrong way or over the first thread, so it enters the line.
  • Connecting malleable iron directly to stainless steel or copper without an insulating joint.

Files and ordering

On this page: Product page (catalogue), MECH Malleable Iron Fittings Catalogue (American Standard), Installation & operation manual, Material Safety Data Sheet (MSDS). Add the product to your request list with size and quantity and we send a quotation. Fu-Mech is the exclusive MECH agent in Saudi Arabia.

Frequently asked questions

What is the difference between a cap and a plug?

A cap closes a male end from outside; a plug closes a female fitting from inside.

Is the thread NPT or BSPT?

This is an American Standard model with NPT threads to ASME B1.20.1. The difference is explained in the guide malleable iron threaded fittings: NPT or BSPT?.

What is the pressure rating?

Rated up to 300 psig from -29 to 66 °C, decreasing with temperature per the MECH pressure-temperature table.

Can they connect to stainless steel or copper pipe?

Per the MECH catalogue, malleable iron threaded fittings must not be connected directly to materials such as stainless steel and copper, because the difference in electrochemical potential causes corrosion. Use a suitable insulating joint.

Are they UL / FM approved?

No approvals are listed for this model in the product data. If your project requires a specific approval, ask us before ordering, or choose from the BS Standard range, which is UL / FM approved.

References

  • ASME B16.3 — Malleable Iron Threaded Fittings: Classes 150 and 300
  • ASTM A197/A197M — Standard Specification for Cupola Malleable Iron
  • ASME B1.20.1 — Pipe Threads, General Purpose, Inch (NPT)
  • MECH catalogue — Malleable Iron Pipe Fittings — American Standard

This guide is general information to help with selection. Figures come from the product data on this page and the MECH catalogue; final design is by the project’s approved designer.