The MECH long adapter m/f in black malleable iron, model 526, BS EN 10242 / ISO 49, material BS EN 1562, BSPT threads (ISO 7-1), sizes 1/2″ × 30 mm – 1/2″ × 100 mm, UL rated pressure 500 psig, UL (EX6624) / FM approved. This guide explains what it does, related models, technical data, correct installation and common mistakes.
At a glance
- A reducing bush fits inside a female fitting to reduce its size: its male thread goes into the larger fitting and its female thread takes the smaller pipe.
- Sizes 1/2″ × 30 mm – 1/2″ × 100 mm, BSPT threads.
- UL rated pressure 500 psig.
- Approvals: UL (EX6624) / FM.
- Equivalent standard model: RC26.
What is a threaded bush and nipple?
A reducing bush fits inside a female fitting to reduce its size: its male thread goes into the larger fitting and its female thread takes the smaller pipe. A hex nipple joins two female fittings, and a reducing nipple joins two sizes.
Extension pieces and long adapters (female × male) extend an outlet by a set length, for example to set a sprinkler head position relative to a suspended ceiling.
Related models
| Model | Item | Sizes |
|---|---|---|
| 529X | SHORT EXTENSION PIECE | 1/2″ |
| 529A | LONG EXTENSION PIECE | 1/4″ – 4″ |
| 526 — this product | LONG ADAPTER M/F | 1/2″ × 30 mm – 1/2″ × 100 mm |
Technical data
| Item | Specification |
|---|---|
| Standard | BS EN 10242 / ISO 49 |
| Material | Malleable cast iron BS EN 1562 |
| Threads | ISO 7-1 (BSPT) |
| Rated pressure (UL) | 500 psig |
| Approvals | UL (EX6624) / FM |
| Equivalent model | RC26 |
| Sizes | 1/2″ × 30 mm – 1/2″ × 100 mm |
Dimensions for every size are in the size table at the top of the page. Per the MECH catalogue: tensile strength ≥ 350 MPa, elongation ≥ 10%.
Joints and pressure loss
Every bush or nipple adds a threaded joint, a possible leak point and extra pressure loss. Use a direct reducing fitting (reducing elbow or tee) where possible instead of a bush plus a standard fitting.
Caution
Never mix NPT and BSPT threads: the joint may seem to make up but it will not seal and will leak under pressure.
Installation steps
- Make sure pipe and fitting have the same thread (BSPT); never mix NPT and BSPT in one joint.
- Clean and inspect the threads, then apply a suitable sealant (PTFE tape or a thread compound approved for the fluid) to the male thread only.
- Screw the fitting on by hand first, then finish with a wrench for a reasonable number of turns without over-tightening; excessive tightening can split the fitting.
- Support the pipework properly so threaded joints do not carry extra weight or bending.
- Pressure-test the line to the project specification before commissioning.
Common mistakes
- Mixing American NPT and British BSPT fittings in the same line.
- Over-tightening with a wrench or using extension bars, cracking the fitting.
- Wrapping PTFE tape the wrong way or over the first thread, so it enters the line.
- Connecting malleable iron directly to stainless steel or copper without an insulating joint.
Files and ordering
On this page: Product page (catalogue), MECH Malleable Iron Fittings Catalogue (BS Standard), Installation & operation manual, Material Safety Data Sheet (MSDS). Add the product to your request list with size and quantity and we send a quotation. Fu-Mech is the exclusive MECH agent in Saudi Arabia.
Frequently asked questions
When should I use a bush instead of a reducing fitting?
When the reducing fitting is not available in the size needed, or when modifying an existing line. In new work a direct reducing fitting is preferred.
Is the thread BSPT or NPT?
This is a BS Standard model with BSPT threads to ISO 7-1. The difference is explained in the guide malleable iron threaded fittings: NPT or BSPT?.
What is the pressure rating?
UL rated pressure 500 psig.
Can they connect to stainless steel or copper pipe?
Per the MECH catalogue, malleable iron threaded fittings must not be connected directly to materials such as stainless steel and copper, because the difference in electrochemical potential causes corrosion. Use a suitable insulating joint.
Are they UL / FM approved?
Yes, per the product data: UL (EX6624) / FM.
References
- BS EN 10242 — Threaded pipe fittings in malleable cast iron
- BS EN 1562 — Founding — Malleable cast irons
- ISO 7-1 — Pipe threads where pressure-tight joints are made on the threads (BSPT)
- MECH catalogue — Malleable Iron Pipe Fittings — BS Standard
This guide is general information to help with selection. Figures come from the product data on this page and the MECH catalogue; final design is by the project’s approved designer.




