The MECH grooved flange pn16, model 321, in ductile iron, sizes 1-1/2″ – 24″ (DN40 – DN600), working pressure up to 300 PSI, UL / FM / VdS / LPCB approved depending on size. This guide explains what it does and how it works, compares it with related models, and covers technical data, the critical point in selection and installation, and common mistakes.
At a glance
- A grooved flange (or flange adaptor) connects a grooved pipe to a flanged fitting, valve or pump without welding a flange on the pipe.
- Sizes 1-1/2″ – 24″ (DN40 – DN600) — working pressure up to 300 PSI.
- Approvals: UL / FM / VdS / LPCB (vary by size).
- Material Ductile iron ASTM A536 Gr. 65-45-12.
- Designed to ASTM F1548, AWWA C606, ISO 6182-12.
What is a grooved flange and how does it work?
A grooved flange (or flange adaptor) connects a grooved pipe to a flanged fitting, valve or pump without welding a flange on the pipe. It locks onto the groove and then bolts to the mating flange.
It saves installation time and lets valves and equipment be removed easily for maintenance; it is the usual transition between a grooved network and flanged equipment.
About model 321: A grooved flange with PN16 drilling.
Models in the same family
| Model | Item | Sizes | Max pressure | Approvals |
|---|---|---|---|---|
| 321 — this product | MECH GROOVED FLANGE PN16 | 1-1/2″ – 24″ | 300 PSI | UL / FM / VdS / LPCB |
| 321G | MECH GROOVED ADAPTOR FLANGE PN16 | 1″ – 18″ | 500 PSI | UL / FM / VdS / LPCB |
| 321GA | MECH GROOVED ADAPTOR | 2″ – 24″ | 300 PSI | UL / FM |
| 321A | MECH GROOVED FLANGES | 2″ – 24″ | 300 PSI | UL |
Technical data
| Item | Specification |
|---|---|
| Design standard | ASTM F1548, AWWA C606, ISO 6182-12 |
| Material | Ductile iron ASTM A536 Gr. 65-45-12 |
| Coating | Electrophoretic (std.) — epoxy / hot-dip galvanized optional |
| Sizes | 1-1/2″ – 24″ (DN40 – DN600) |
| Approvals | Sizes | Working pressure |
|---|---|---|
| UL / FM / VdS / LPCB | 1-1/2″ – 8″ | 300 PSI |
| UL / FM | 4″ – 12″ | 300 PSI |
| UL / FM / LPCB | 6″ | 300 PSI |
| UL / FM / VdS | 10″ | 300 PSI |
| UL | 14″ | 300 PSI |
| Not stated in the table | 16″ – 24″ | 300 PSI |
Some sizes come in two pipe outside diameters (for example 73.0 and 76.1 mm for 2-1/2″) depending on the pipe standard; select by the actual outside diameter of your project pipe.
Full dimensions for every size (bolts and more) are in the size table at the top of the page.
Matching the flange standard
The bolt holes must match the mating flange (for example PN16 or ANSI), and the mating flange face must suit the grooved flange gasket.
Caution
Check the drilling standard in the product table or catalogue before ordering, and confirm the mating flange face per MECH instructions.
Installation steps
- Check that the pipe ends are grooved to the right dimensions to AWWA C606 (roll or cut groove) and are free of burrs, rust and dirt.
- Inspect the gasket and lubricate its outside and lips with the lubricant recommended in the MECH catalogue; never use petroleum-based products with an EPDM gasket.
- Fit the gasket over one pipe end, bring the other end or the fitting into place, and slide the gasket so it is centred between the two grooves.
- Place both housing halves over the gasket so their keys engage the grooves on both sides.
- Hand-tighten the nuts first, making sure each oval-neck bolt sits in its hole, then tighten alternately and evenly to the torque in the MECH installation manual — never exceed it.
The fitting joins with grooved couplings; how the joint is finished (even pad gap or pads meeting) follows the coupling type in the MECH manual.
Full details and bolt torques are in the MECH installation manual among the files on this page.
Common mistakes
- Letting the gasket lip overhang the pipe end or protrude into a groove, so the gasket is not centred on the joint.
- Exceeding the specified bolt torque, which can damage the bolt or the joint.
- Grooves that do not meet AWWA C606 dimensions, or pipe ends that are not square.
- Tightening the nuts on one side only, so the housing tilts and the key does not seat in the groove.
- Using petroleum-based lubricant that damages the EPDM gasket.
Files and ordering
On this page: Product page (catalogue), MECH Grooved Fittings & Couplings Catalogue, Installation & operation manual, Material Safety Data Sheet (MSDS). Add the product to your request list with size and quantity and we send a quotation, or build a submittal PDF for the consultant. Fu-Mech is the exclusive MECH agent in Saudi Arabia.
Frequently asked questions
Does it need welding?
No. It locks onto the pipe groove and bolts to the mating flange.
What is the maximum working pressure of model 321?
Up to 300 PSI. The pressure for each size is in the size table.
Is model 321 UL / FM approved?
Approvals for this model: UL / FM / VdS / LPCB, varying by size as shown in the “Approvals and pressure by size” table above. See also how to verify UL and FM approvals.
What is the gasket material, and does it suit all fluids?
Gasket type and suitable services are given in the MECH catalogue.
Does it suit roll-grooved and cut-grooved pipe?
Grooves are to AWWA C606, rolled or cut; what matters is correct groove dimensions. The difference is explained in the guide roll grooving vs cut grooving.
References
- ASTM F1548 — Standard Specification for Performance of Fittings for Use with Gasketed Mechanical Couplings Used in Piping Applications
- AWWA C606 — Grooved and Shouldered Joints
- ISO 6182-12 — Fire protection — Automatic sprinkler systems — Requirements and test methods for grooved-end components for steel pipe systems
- ASTM A536 — Standard Specification for Ductile Iron Castings
- UL 213 — Rubber Gasketed Fittings for Fire-Protection Service
- FM 1920 — Approval Standard for Pipe Couplings and Fittings for Fire Protection Systems
- MECH catalogue — Grooved Fittings & Couplings — and installation manual
This guide is general information to help with selection. Figures come from the product data on this page and the MECH catalogue; final design is by the project’s approved designer to NFPA 13 and the project specification.




