Skip to content
Exclusive agent of MECH products in Saudi Arabia
Store Request a quote

MECH BRASS BALL VALVE MODEL : Q11F-231A

Model Q11F-231A

Connection standard
ASME B1.20.1 (NPT)
Working pressure
400 PSI
Temperature
-20 – 120 °C
Application
WOG (water, oil, gas)
Body material
Brass CW617N
Seat
PTFE
Sizes
1/2" – 2" (DN15 – DN50)
Request a quote for this product
Or buy from the online store
Certificates & approvals

Ask us for this product's certificates.

SIZES & DIMENSIONS

Sizes & dimensions

SizeDNA (mm)ΦB (mm)D (mm)E ThreadH Height (mm)L Handle length (mm)
1/2"DN154512.5101/2 NPT50102
3/4"DN2057.318133/4 NPT54.5102
1"DN25692215.51 NPT60125
1 1/4"DN3275.630151 1/4 NPT74125
1 1/2"DN408536161 1/2 NPT84150
2"DN5010045182 NPT93150

The MECH brass ball valve, model Q11F-231A, sizes 1/2″ – 2″ (DN15 – DN50), working pressure 400 PSI. A quick quarter-turn shut-off valve. This guide explains what it does and how it works, related models, technical data, the critical point in selection and installation, and common mistakes.

At a glance

  • A ball valve has a bored ball that turns a quarter turn: bore in line means open, across means shut.
  • Sizes 1/2″ – 2″ (DN15 – DN50).
  • Working pressure 400 PSI.
  • Connection: Threaded NPT — ASME B1.20.1.
  • Operating temperature: -20 – 120 °C.

Brass ball valve: what it does and how it works

A ball valve has a bored ball that turns a quarter turn: bore in line means open, across means shut. It seals on PTFE seats.

It is used for isolation on small water, air and service lines, and its handle shows its position at a glance.

Technical data

Specification of model Q11F-231A
ItemSpecification
Design standardGB/T 8464
Connection endsThreaded NPT — ASME B1.20.1
Working pressure400 PSI
Temperature range-20 – 120 °C
Body materialBrass CW617N
SeatPTFE
ServiceWOG (water, oil, gas)
Sizes1/2″ – 2″ (DN15 – DN50)

Parallel or taper thread

An ISO 228 parallel thread does not seal by interference, so sealing relies on a gasket, washer or suitable compound; NPT and ISO 7-1 are taper threads that seal on the thread with sealant. Choose the valve with the same thread as the pipe and fittings.

Caution

A ball valve is for full open or shut; throttling with it damages the seats.

Installation steps

  1. Check the thread type (ISO 228 parallel or NPT / ISO 7-1 taper) matches the pipe, and use the sealant or gasket suited to that thread.
  2. Hold the valve with the wrench on the end being tightened, not on the body or handle.
  3. Do not over-tighten, so the brass body is not distorted.
  4. Operate the valve after installation to check movement and sealing.

Common mistakes

  • Mixing parallel and taper threads.
  • Tightening by the valve body or handle.
  • Over-tightening the brass body.

Files and ordering

On this page: MECH Brass Valves Catalogue. Add the product to your request list with size and quantity and we send a quotation, or build a submittal PDF for the consultant. Fu-Mech is the exclusive MECH agent in Saudi Arabia.

Frequently asked questions

Can it be used to throttle flow?

No, it is for full open and shut.

What service is it for?

Per the MECH catalogue, WOG service: water, oil and gas.

What is the working pressure of model Q11F-231A?

400 PSI per the product data. The pressure for each size or listed model is in the size table and datasheet.

What end connection does it have?

Threaded NPT — ASME B1.20.1. Choose the connection that matches the adjacent pipe and fittings.

References

  • ASME B1.20.1 — Pipe Threads, General Purpose, Inch (NPT)
  • MECH catalogue — MECH brass valves

This guide is general information to help with selection. Figures come from the product data on this page and the MECH catalogue; final design is by the project’s approved designer to the applicable standards and the project specification.