Skip to content
Exclusive agent of MECH products in Saudi Arabia
Store Request a quote

MECH GROOVED FLEXIBLE COUPLING -MODEL 1N

Model 1N

Design standard
ASTM F1476, EN 10311
Material
Ductile iron ASTM A536 Gr. 65-45-12
Coating
Electrophoretic (std.) — epoxy / hot-dip galvanized optional
Gasket
Grade "E" EPDM (fire sprinkler)
Sizes
1" – 24" (DN25 – DN600)
Request a quote for this product
Or buy from the online store
SIZES & DIMENSIONS

Sizes & dimensions

SizeDNPipe OD (mm)Max working pressure (PSI)Max end load (kN/lbs)Pipe end separation (mm)A (mm)B (mm)C (mm)Bolts (No.-Size)Certificate
1"DN2533.75003.0/6800-1.65592422-3/8×55 / 2-M10×57VdS / UL / FM / LPCB
1-1/4"DN3242.45004.8/10800-1.665104442-3/8×55 / 2-M10×57VdS / UL / FM / LPCB
1-1/2"DN4048.35006.3/14200-3.270110442-3/8×55 / 2-M10×57VdS / UL / FM / LPCB
2"DN5060.35009.8/22100-3.283125442-3/8×55 / 2-M10×57VdS / UL / FM / LPCB
2-1/2"DN6573.050014.4/32400-3.296143452-3/8×55 / 2-M10×57UL / FM / LPCB
2-1/2"DN6576.150015.7/35200-3.2100145452-3/8×55 / 2-M10×57VdS / UL / FM / LPCB
3"DN8088.950021.4/48100-3.2115160452-1/2×70 / 2-M12×70VdS / UL / FM / LPCB
4"DN100108.050031.5/71000-3.2138190502-1/2×70 / 2-M12×70UL / FM / LPCB
4"DN100114.350035.4/79600-3.2145198502-1/2×70 / 2-M12×70VdS / UL / FM / LPCB
5"DN12513330028.7/64600-3.216222551.02-5/8×80 / 2-M16×85UL / FM / LPCB
5"DN125139.750052.9/118000-3.2169230522-5/8×80 / 2-M16×85VdS / UL / FM / LPCB
5"DN125141.350054.1/121000-3.2170232512-5/8×80 / 2-M16×85UL / FM / LPCB
6"DN150159.030041.0/92400-3.2190256522-5/8×85 / 2-M16×85UL / FM / LPCB
6"DN150165.150073.8/166100-3.2196260522-5/8×85 / 2-M16×85UL / FM / LPCB
6"DN150168.350076.7/172600-3.2200265522-5/8×85 / 2-M16×85VdS / UL / FM / LPCB
8"DN200216.330076.0/171000-3.2254320592-5/8×85 / 2-M16×85FM
8"DN200219.1500116.9/262800-3.2258342602-3/4×115 / 2-M20×115VdS / UL / FM / LPCB
10"DN250267.4300116.2/261400-3.2308.5403642-3/4×115 / 2-M20×115FM
10"DN250273.0500121.0/272100-3.2337406652-7/8×140 / 2-M22×140UL / FM / VdS
12"DN300318.5300164.8/370900-3.2363460632-7/8×140 / 2-M22×140FM
12"DN300323.9500170.3/382800-3.2378465652-7/8×140 / 2-M22×140UL / FM
14"DN350355.6300205.5/462200-3.2402493723-7/8×140 / 3-M22×140UL
14"DN350377.0225178.5/401600-3.2428520723-7/8X140 / 3-M22X140UL
16"DN400406.4300268.4/603700-3.2458547723-7/8×140 / 3-M22×140UL
16"DN400426.0225227.9/512700-3.2476566733-7/8X140 / 3-M22X140UL
18"DN450457.2300262.5/590600-3.2505598783-7/8×140 / 3-M22×140UL
18"DN450480.0300373.8/841100-3.2533628783-7/8X140 / 3-M22X140UL
20"DN500508.0300324.1/729100-3.2550648784-7/8×140 / 4-M22×140UL
24"DN600609.6300466.7/1049900-3.2662774784-1X140UL
PROJECT APPROVALS

Approved on projects

112 projects and 77 owners approved this product or its family through the project consultants.

and 100 more projects.

Original approval letters are provided on request with your submittal.

The MECH grooved flexible coupling, model 1N, in ductile iron, sizes 1″ – 24″ (DN25 – DN600), working pressure up to 500 PSI depending on size, UL / FM / VdS / LPCB approved depending on size. This guide explains what it does and how it works, compares it with related models, and covers technical data, the critical point in selection and installation, and common mistakes. For more, read the technical library guide.

At a glance

  • A flexible coupling joins two grooved ends, but the housing leaves a designed clearance in the groove, allowing limited angular deflection, axial movement and rotation at the joint.
  • Sizes 1″ – 24″ (DN25 – DN600) — working pressure up to 500 PSI depending on size.
  • Approvals: UL / FM / VdS / LPCB (vary by size).
  • Material Ductile iron ASTM A536 Gr. 65-45-12, gasket Grade “E” EPDM (fire sprinkler).
  • Designed to ASTM F1476, EN 10311.

What is a grooved flexible coupling and how does it work?

A flexible coupling joins two grooved ends, but the housing leaves a designed clearance in the groove, allowing limited angular deflection, axial movement and rotation at the joint.

This flexibility absorbs thermal expansion and contraction, isolates pump and equipment vibration, accommodates building settlement and seismic movement, and eases installation where the line has slight misalignment.

Models in the same family

MECH grooved flexible coupling family
ModelItemSizesMax pressureApprovals
1NSMECH GROOVED FLEXIBLE COUPLING2″ – 10″450 PSIUL
1NHMECH GROOVED HEAVY COUPLING2″ – 18″750 PSIUL / FM
1NXMECH GROOVED FLEXIBLE COUPLING2″ – 10″363 PSIUL / FM
1N — this productMECH GROOVED FLEXIBLE COUPLING1″ – 24″500 PSIUL / FM / VdS / LPCB

Technical data

Model 1N specification
ItemSpecification
Design standardASTM F1476, EN 10311
MaterialDuctile iron ASTM A536 Gr. 65-45-12
CoatingElectrophoretic (std.) — epoxy / hot-dip galvanized optional
GasketGrade “E” EPDM (fire sprinkler)
Sizes1″ – 24″ (DN25 – DN600)
Approvals and pressure by size
ApprovalsSizesWorking pressure
UL / FM / VdS / LPCB1″ – 8″500 PSI
UL / FM / LPCB2-1/2″ – 6″300–500 PSI
FM8″ – 12″300 PSI
UL / FM / VdS10″500 PSI
UL / FM12″500 PSI
UL14″ – 24″225–300 PSI

Some sizes come in two pipe outside diameters (for example 73.0 and 76.1 mm for 2-1/2″) depending on the pipe standard; select by the actual outside diameter of your project pipe.

Full dimensions for every size (bolts and more) are in the size table at the top of the page.

Movement and pressure thrust

Because a flexible joint allows movement, internal pressure can push the pipes apart up to the maximum gap. Lines with flexible couplings therefore need supports and anchors designed for it.

Caution

The number and position of flexible couplings, supports and anchors are set by the project’s approved designer, especially for seismic protection.

Installation steps

  1. Check that the pipe ends are grooved to the right dimensions to AWWA C606 (roll or cut groove) and are free of burrs, rust and dirt.
  2. Inspect the gasket and lubricate its outside and lips with the lubricant recommended in the MECH catalogue; never use petroleum-based products with an EPDM gasket.
  3. Fit the gasket over one pipe end, bring the other end or the fitting into place, and slide the gasket so it is centred between the two grooves.
  4. Place both housing halves over the gasket so their keys engage the grooves on both sides.
  5. Hand-tighten the nuts first, making sure each oval-neck bolt sits in its hole, then tighten alternately and evenly to the torque in the MECH installation manual — never exceed it.

On a flexible coupling, tighten until the two housings meet metal to metal, with no gasket visible from outside.

Full details and bolt torques are in the MECH installation manual among the files on this page.

Common mistakes

  • Letting the gasket lip overhang the pipe end or protrude into a groove, so the gasket is not centred on the joint.
  • Exceeding the specified bolt torque, which can damage the bolt or the joint.
  • Grooves that do not meet AWWA C606 dimensions, or pipe ends that are not square.
  • Tightening the nuts on one side only, so the housing tilts and the key does not seat in the groove.
  • Using petroleum-based lubricant that damages the EPDM gasket.

Files and ordering

On this page: Product page (catalogue), Product page (catalogue), MECH Grooved Fittings & Couplings Catalogue, Installation & operation manual, Material Safety Data Sheet (MSDS). Add the product to your request list with size and quantity and we send a quotation, or build a submittal PDF for the consultant. Fu-Mech is the exclusive MECH agent in Saudi Arabia.

Frequently asked questions

Where should I use a flexible coupling?

At pump and equipment connections to isolate vibration, on lines subject to thermal expansion, and at building expansion and seismic joints. See the guide rigid vs flexible grooved couplings.

What is the maximum working pressure of model 1N?

Up to 500 PSI depending on size (from 225 to 500). The pressure for each size is in the size table.

Is model 1N UL / FM approved?

Approvals for this model: UL / FM / VdS / LPCB, varying by size as shown in the “Approvals and pressure by size” table above. See also how to verify UL and FM approvals.

What is the gasket material, and does it suit all fluids?

The gasket is Grade “E” EPDM (fire sprinkler). EPDM suits water and sprinkler systems but not oils or petroleum products; for any other fluid check the MECH catalogue or ask us.

Does it suit roll-grooved and cut-grooved pipe?

Grooves are to AWWA C606, rolled or cut; what matters is correct groove dimensions. The difference is explained in the guide roll grooving vs cut grooving.

References

  • ASTM F1476 — Standard Specification for Performance of Gasketed Mechanical Couplings for Use in Piping Applications
  • EN 10311 — Joints for the connection of steel tubes and fittings for the conveyance of water and other aqueous liquids
  • ASTM A536 — Standard Specification for Ductile Iron Castings
  • UL 213 — Rubber Gasketed Fittings for Fire-Protection Service
  • FM 1920 — Approval Standard for Pipe Couplings and Fittings for Fire Protection Systems
  • MECH catalogue — Grooved Fittings & Couplings — and installation manual

This guide is general information to help with selection. Figures come from the product data on this page and the MECH catalogue; final design is by the project’s approved designer to NFPA 13 and the project specification.