Skip to content
Exclusive agent of MECH products in Saudi Arabia
Store Request a quote

BS Standard MECH BMI SHORT BEND 90° M/F | MODEL 1A

Model 1A

Standard
BS EN 10242 / ISO 49
Material
Malleable cast iron BS EN 1562
Threads
ISO 7-1 (BSPT)
Rated pressure (UL)
500 psig
Approvals
UL (EX6624) / FM
Equivalent model
E1A
Sizes
1/4" – 4"
Request a quote for this product
Or buy from the online store
SIZES & DIMENSIONS

Sizes & dimensions

SizeDNA (mm)
1/4"DN830
3/8"DN1036
1/2"DN1545
3/4"DN2050
1"DN2563
1-1/4"DN3276
1-1/2"DN4085
2"DN50102
2-1/2"DN65115
3"DN80138
4"DN100167
PROJECT APPROVALS

Approved on projects

96 projects and 64 owners approved this product or its family through the project consultants.

and 84 more projects.

Original approval letters are provided on request with your submittal.

The MECH short bend 90° m/f in black malleable iron, model 1A, BS EN 10242 / ISO 49, material BS EN 1562, BSPT threads (ISO 7-1), sizes 1/4″ – 4″, UL rated pressure 500 psig, UL (EX6624) / FM approved. This guide explains what it does, related models, technical data, correct installation and common mistakes.

At a glance

  • A bend changes direction with a larger radius than a standard elbow, giving smoother flow and lower pressure loss.
  • Sizes 1/4″ – 4″, BSPT threads.
  • UL rated pressure 500 psig.
  • Approvals: UL (EX6624) / FM.
  • Equivalent standard model: E1A.

What is a threaded bend?

A bend changes direction with a larger radius than a standard elbow, giving smoother flow and lower pressure loss. It comes in 90° or 45°, with female, male or female × male ends depending on the model; a short bend has a smaller radius to save space.

A crossover is a form of bend that lifts the line over another pipe and returns it to level, so two lines cross without meeting.

Related models

BS Standard models of the same type
ModelItemSizes
85CROSSOVER1/2″ – 2″
41BEND 45° FEMALE1/4″ – 6″
40BEND 45° M/F1/4″ – 6″
2ASHORT BEND 90° FEMALE1/2″ – 4″
1A — this productSHORT BEND 90° M/F1/4″ – 4″
3#BEND 90° MALE3/8″ – 4″
2#BEND 90° FEMALE1/4″ – 4″
1#BEND 90° M/F1/8″ – 6″

Technical data

Model 1A specification
ItemSpecification
StandardBS EN 10242 / ISO 49
MaterialMalleable cast iron BS EN 1562
ThreadsISO 7-1 (BSPT)
Rated pressure (UL)500 psig
ApprovalsUL (EX6624) / FM
Equivalent modelE1A
Sizes1/4″ – 4″

Dimensions for every size are in the size table at the top of the page. Per the MECH catalogue: tensile strength ≥ 350 MPa, elongation ≥ 10%.

Elbow or bend?

A bend is hydraulically better because of its wider radius but takes more space. Where pressure loss matters choose a bend; in tight spaces an elbow or short bend.

Caution

Never mix NPT and BSPT threads: the joint may seem to make up but it will not seal and will leak under pressure.

Installation steps

  1. Make sure pipe and fitting have the same thread (BSPT); never mix NPT and BSPT in one joint.
  2. Clean and inspect the threads, then apply a suitable sealant (PTFE tape or a thread compound approved for the fluid) to the male thread only.
  3. Screw the fitting on by hand first, then finish with a wrench for a reasonable number of turns without over-tightening; excessive tightening can split the fitting.
  4. Support the pipework properly so threaded joints do not carry extra weight or bending.
  5. Pressure-test the line to the project specification before commissioning.

Common mistakes

  • Mixing American NPT and British BSPT fittings in the same line.
  • Over-tightening with a wrench or using extension bars, cracking the fitting.
  • Wrapping PTFE tape the wrong way or over the first thread, so it enters the line.
  • Connecting malleable iron directly to stainless steel or copper without an insulating joint.

Files and ordering

On this page: Product page (catalogue), MECH Malleable Iron Fittings Catalogue (BS Standard), Installation & operation manual, Material Safety Data Sheet (MSDS). Add the product to your request list with size and quantity and we send a quotation. Fu-Mech is the exclusive MECH agent in Saudi Arabia.

Frequently asked questions

What is the difference between an elbow and a bend?

A bend has a larger radius, so pressure loss is lower and flow smoother, but it is longer than an elbow.

Is the thread BSPT or NPT?

This is a BS Standard model with BSPT threads to ISO 7-1. The difference is explained in the guide malleable iron threaded fittings: NPT or BSPT?.

What is the pressure rating?

UL rated pressure 500 psig.

Can they connect to stainless steel or copper pipe?

Per the MECH catalogue, malleable iron threaded fittings must not be connected directly to materials such as stainless steel and copper, because the difference in electrochemical potential causes corrosion. Use a suitable insulating joint.

Are they UL / FM approved?

Yes, per the product data: UL (EX6624) / FM.

References

  • BS EN 10242 — Threaded pipe fittings in malleable cast iron
  • BS EN 1562 — Founding — Malleable cast irons
  • ISO 7-1 — Pipe threads where pressure-tight joints are made on the threads (BSPT)
  • MECH catalogue — Malleable Iron Pipe Fittings — BS Standard

This guide is general information to help with selection. Figures come from the product data on this page and the MECH catalogue; final design is by the project’s approved designer.