The MECH grooved elbow 22.5, model 110X (slim-type model), in ductile iron, sizes 4″ – 6″ (DN100 – DN150), working pressure up to 300 PSI, UL / FM approved depending on size. This guide explains what it does and how it works, compares it with related models, and covers technical data, the critical point in selection and installation, and common mistakes. For more, read the technical library guide.
At a glance
- A grooved elbow changes the direction of a line by a set angle; both ends are grooved to join with grooved couplings without welding.
- Sizes 4″ – 6″ (DN100 – DN150) — working pressure up to 300 PSI.
- Approvals: UL / FM.
- Material Ductile iron ASTM A536 Gr. 65-45-12.
- Designed to ASTM F1548, AWWA C606, ISO 6182-12.
What is a grooved elbow and how does it work?
A grooved elbow changes the direction of a line by a set angle; both ends are grooved to join with grooved couplings without welding. MECH angles are 90°, 45°, 22.5° and 11.25°; the small angles are useful for slight offsets and avoiding obstructions.
It is cast in ductile iron with a designed bend radius that reduces pressure loss compared with an abrupt change of direction.
This is the slim-type model. Compare its sizes, pressure and approvals with the other models in the table below.
Models in the same family
| Model | Item | Sizes | Max pressure | Approvals |
|---|---|---|---|---|
| 90C | MECH GROOVED HYDRANT ELBOW 90 | 4″ × 3″ × 1″ – 6″ × 3″ × 1″ | 300 PSI | UL / FM |
| 90R | MECH GROOVED REDUCING ELBOW 90 | 3″ × 2-1/2″ – 6″ × 4″ | 500 PSI | UL / FM |
| 110X — this product | MECH GROOVED ELBOW 22.5 | 4″ – 6″ | 300 PSI | UL / FM |
| 105 | MECH GROOVED ELBOW 11.25 | 1-1/4″ – 8″ | 500 PSI | UL / FM / VdS / LPCB |
| 110 | MECH GROOVED ELBOW 22.5 | 1-1/4″ – 8″ | 500 PSI | UL / FM / VdS / LPCB |
| 120X | MECH GROOVED ELBOW 45 | 3″ – 10″ | 300 PSI | UL / FM |
| 120 | MECH GROOVED ELBOW 45 | 1″ – 24″ | 500 PSI | UL / FM / VdS / LPCB |
| 90X | MECH GROOVED ELBOW 90 | 3″ – 12″ | 300 PSI | UL / FM |
| 90S | MECH GROOVED ELBOW 90 | 2″ – 8″ | 500 PSI | UL / FM / VdS / LPCB |
| 90 | MECH GROOVED ELBOW 90 | 1″ – 24″ | 500 PSI | UL / FM / VdS / LPCB |
Technical data
| Item | Specification |
|---|---|
| Design standard | ASTM F1548, AWWA C606, ISO 6182-12 |
| Material | Ductile iron ASTM A536 Gr. 65-45-12 |
| Coating | Electrophoretic (std.) — epoxy / hot-dip galvanized optional |
| Sizes | 4″ – 6″ (DN100 – DN150) |
| Approvals | Sizes | Working pressure |
|---|---|---|
| UL / FM | 4″ – 6″ | 300 PSI |
Some sizes come in two pipe outside diameters (for example 73.0 and 76.1 mm for 2-1/2″) depending on the pipe standard; select by the actual outside diameter of your project pipe.
Full dimensions for every size (bolts and more) are in the size table at the top of the page.
Support at changes of direction
Every change of direction creates thrust from water pressure and the change in flow direction, so lines need suitable supports or anchors at elbows, particularly with flexible couplings.
Caution
Select the elbow by size and pressure from the product table; support positions are set by the approved designer to NFPA 13 and the project specification.
Installation steps
- Check that the pipe ends are grooved to the right dimensions to AWWA C606 (roll or cut groove) and are free of burrs, rust and dirt.
- Inspect the gasket and lubricate its outside and lips with the lubricant recommended in the MECH catalogue; never use petroleum-based products with an EPDM gasket.
- Fit the gasket over one pipe end, bring the other end or the fitting into place, and slide the gasket so it is centred between the two grooves.
- Place both housing halves over the gasket so their keys engage the grooves on both sides.
- Hand-tighten the nuts first, making sure each oval-neck bolt sits in its hole, then tighten alternately and evenly to the torque in the MECH installation manual — never exceed it.
The fitting joins with grooved couplings; how the joint is finished (even pad gap or pads meeting) follows the coupling type in the MECH manual.
Full details and bolt torques are in the MECH installation manual among the files on this page.
Common mistakes
- Letting the gasket lip overhang the pipe end or protrude into a groove, so the gasket is not centred on the joint.
- Exceeding the specified bolt torque, which can damage the bolt or the joint.
- Grooves that do not meet AWWA C606 dimensions, or pipe ends that are not square.
- Tightening the nuts on one side only, so the housing tilts and the key does not seat in the groove.
- Using petroleum-based lubricant that damages the EPDM gasket.
Files and ordering
On this page: Product page (catalogue), MECH Grooved Fittings & Couplings Catalogue, Installation & operation manual, Material Safety Data Sheet (MSDS). Add the product to your request list with size and quantity and we send a quotation, or build a submittal PDF for the consultant. Fu-Mech is the exclusive MECH agent in Saudi Arabia.
Frequently asked questions
How do I choose the elbow angle?
By the change of direction the route needs: 90° for a full turn, 45° for a medium turn or an offset with two elbows, 22.5° and 11.25° for slight deviations. See the guide grooved elbows.
What is the maximum working pressure of model 110X?
Up to 300 PSI. The pressure for each size is in the size table.
Is model 110X UL / FM approved?
Yes. Approvals by size: UL / FM for 4″ – 6″. See the size table on this page and the guide how to verify UL and FM approvals.
What is the gasket material, and does it suit all fluids?
Gasket type and suitable services are given in the MECH catalogue.
Does it suit roll-grooved and cut-grooved pipe?
Grooves are to AWWA C606, rolled or cut; what matters is correct groove dimensions. The difference is explained in the guide roll grooving vs cut grooving.
References
- ASTM F1548 — Standard Specification for Performance of Fittings for Use with Gasketed Mechanical Couplings Used in Piping Applications
- AWWA C606 — Grooved and Shouldered Joints
- ISO 6182-12 — Fire protection — Automatic sprinkler systems — Requirements and test methods for grooved-end components for steel pipe systems
- ASTM A536 — Standard Specification for Ductile Iron Castings
- UL 213 — Rubber Gasketed Fittings for Fire-Protection Service
- FM 1920 — Approval Standard for Pipe Couplings and Fittings for Fire Protection Systems
- MECH catalogue — Grooved Fittings & Couplings — and installation manual
This guide is general information to help with selection. Figures come from the product data on this page and the MECH catalogue; final design is by the project’s approved designer to NFPA 13 and the project specification.




