Skip to content
Exclusive agent of MECH products in Saudi Arabia
Store Request a quote

MECH FLEXIBLE RUBBER JOINT UNION MODEL : XTQ2L

Model XTQ2L

Connection ends
Thread ASME B1.20.1
Working pressure
300 PSI (200 / 250 PSI on request)
Temperature
0 – 80 °C
Vacuum
500 mmHg
Sizes
1/2" – 3" (DN15 – DN80)
Request a quote for this product
Or buy from the online store
SIZES & DIMENSIONS

Sizes & dimensions

SizeDNL Length (mm)X Thread NPTAxial elongation (mm)Axial compression (mm)Transverse movement (mm)Angular deflection (°)
1/2"DN152001/2-146222240
3/4"DN202003/4-146222240
1"DN252001-11.56222240
1-1/4"DN322001 1/4-11.56222240
1-1/2"DN402001 1/2-11.56222240
2"DN502002-11.56222240
2-1/2"DN652402 1/2-86222240
3"DN802403-86222240

The MECH flexible rubber joint union, model XTQ2L, sizes 1/2″ – 3″ (DN15 – DN80), working pressure 300 PSI (200 / 250 PSI on request). It absorbs vibration and small movements and isolates noise at pumps and equipment. This guide explains what it does and how it works, related models, technical data, the critical point in selection and installation, and common mistakes. For more, read the guide flexible rubber joints.

At a glance

  • A flexible rubber joint is a reinforced rubber body between two end connections (flanges or a threaded union).
  • Sizes 1/2″ – 3″ (DN15 – DN80).
  • Working pressure 300 PSI (200 / 250 PSI on request).
  • Connection: Thread ASME B1.20.1.
  • Operating temperature: 0 – 80 °C.

Flexible rubber joint: what it does and how it works

A flexible rubber joint is a reinforced rubber body between two end connections (flanges or a threaded union). It absorbs pump and equipment vibration, small thermal movement and slight misalignment, and reduces noise transmitted to the pipework.

It also withstands vacuum up to the limit in the product data, which matters on pump suction lines.

Related models

flexible rubber joint family
ModelProductSizesPressureApprovals
XTQ2L — this productFLEXIBLE RUBBER JOINT UNION1/2″ – 3″ (DN15 – DN80)300 PSI—
XTQ1RFFLEXIBLE RUBBER JOINT FLANGED1-1/4″ – 24″ (DN32 – DN600)300 PSI—

Technical data

Specification of model XTQ2L
ItemSpecification
Connection endsThread ASME B1.20.1
Working pressure300 PSI (200 / 250 PSI on request)
Temperature0 – 80 °C
Vacuum500 mmHg
Sizes1/2″ – 3″ (DN15 – DN80)

Dimensions for every size are in the size table at the top of the page.

Support and thrust

A flexible joint carries neither the weight of the line nor the pressure thrust. The pipe must be supported and anchored on both sides, with control rods where needed per the manufacturer’s instructions.

Caution

Do not use the joint to correct large misalignment, and never paint the rubber body.

Installation steps

  1. Install the joint close to the vibrating equipment.
  2. Make sure the pipes on both sides are aligned and supported before tightening.
  3. Tighten bolts alternately and evenly without over-tightening.
  4. Inspect the joint after start-up and after the first temperature rise.

Common mistakes

  • Letting the line weight hang on the joint.
  • Using it to fix large misalignment.
  • Painting the rubber body or exposing it to petroleum products.

Files and ordering

On this page: Product datasheet, MECH Fire Protection Valves Catalogue (UL/FM). Add the product to your request list with size and quantity and we send a quotation, or build a submittal PDF for the consultant. Fu-Mech is the exclusive MECH agent in Saudi Arabia.

Frequently asked questions

Where is it installed?

On pump suction and discharge and at vibrating equipment. See flexible rubber joints.

Does it withstand vacuum?

Yes, up to the vacuum limit in the product data.

What is the working pressure of model XTQ2L?

300 PSI (200 / 250 PSI on request) per the product data. The pressure for each size or listed model is in the size table and datasheet.

What end connection does it have?

Thread ASME B1.20.1. Choose the connection that matches the adjacent pipe and fittings.

References

  • ASME B1.20.1 — Pipe Threads, General Purpose, Inch (NPT)
  • MECH catalogue — Product datasheet

This guide is general information to help with selection. Figures come from the product data on this page and the MECH catalogue; final design is by the project’s approved designer to the applicable standards and the project specification.